思科幀中繼點對多點子接口配置實例解析

    時間:2024-08-15 07:02:57 網絡技術 我要投稿
    • 相關推薦

    思科幀中繼點對多點子接口配置實例解析

      Cisco ACE是一個很常用的配置,下面小編為大家介紹了Cisco ACE的一個基本配置實例,希望大家能夠輕松掌握。

      幀中繼點對多點子接口拓撲圖如下:

      步驟一:配置R4的為幀中繼交換機。

      R4(config)#frame-relay switching //啟用frame-relay 交換

      R4(config)#interface serial 1/0

      R4(config-if)#encapsulation frame-relay

      R4(config-if)#frame-relay intf-type dce

      R4(config-if)#frame-relay lmi-type cisco (默認類型)

      R4(config-if)#frame-relay route 100 interface serial 1/1 101

      R4(config-if)#frame-relay route 200 interface serial 1/2 201

      R4(config-if)#clock rate 64000

      R4(config-if)#no shutdown

      R4(config-if)#exit

      R4(config)#interface serial 1/1

      R4(config-if)#encapsulation frame-relay

      R4(config-if)#frame-relay intf-type dce

      R4(config-if)#frame-relay lmi-type ansi

      R4(config-if)#frame-relay route 101 interface serial 1/0 100

      R4(config-if)#clock rate 64000

      R4(config-if)#no shutdown

      R4(config-if)#exit

      R4(config)#interface serial 1/2

      R4(config-if)#encapsulation frame-relay

      R4(config-if)#frame-relay intf-type dce

      R4(config-if)#frame-relay lmi-type q933a

      R4(config-if)#frame-relay route 201 interface serial 1/0 200

      R4(config-if)#clock rate 64000

      R4(config-if)#no shutdown

      步驟二:配置R2路由器

      R2(config)#interface serial 1/2

      R2(config-if)#encapsulation frame-relay //在接口下啟用幀中繼的封裝

      R2(config-if)#ip address 172.16.1.2 255.255.255.0

      R2(config-if)#no shut

      步驟三:配置R3路由器

      R3(config)#interface serial 1/2

      R3(config-if)#encapsulation frame-relay

      R3(config-if)#ip address 172.16.1.3 255.255.255.0

      R3(config-if)#no shut

      步驟四:配置R1,采用多點子接口,配置R1的幀中繼

      R1(config)#interface serial 1/2

      R1(config-if)#encapsulation frame-relay

      R1(config-if)#no ip add

      R1(config-if)#no shut

      R1(config-if)#exit

      R1(config)#interface serial 1/2.1 multipoint

      R1(config-subif)#ip address 172.16.1.1 255.255.255.0

      R1(config-subif)#frame-relay map ip 172.16.1.2 100 broadcast

      R1(config-subif)#frame-relay map ip 172.16.1.3 200 broadcast

      R1(config-subif)#exit

      R1(config)#exit

      步驟五:在R1使用show frame-realy lmi,show frame-relay pvc進行確認。

      步驟六:在R1,R2,R3上配置RIP,進行觀察。

      幀中繼點對多點子接口配置結果:R1,R2,R3能夠正確的學習到所有的路由。

    【思科幀中繼點對多點子接口配置實例解析】相關文章:

    思科DHCP服務器配置實例解析07-25

    思科三層交換機配置實例及命令10-24

    思科配置命令詳細介紹01-23

    EIGRP帶寬實例配置09-19

    思科交換機的基本配置09-10

    思科交換機配置vlan09-02

    思科路由器的安全配置06-03

    思科路由器配置基礎08-13

    思科交換機STP配置08-30

    cisco思科交換機配置篇08-01

    91久久大香伊蕉在人线_国产综合色产在线观看_欧美亚洲人成网站在线观看_亚洲第一无码精品立川理惠

      五月天婷五月天综合网在线 | 一区二区三区AV免费 | 欧美亚洲精品免费 | 综合久久久综合欧美98 | 日本无卡码高清免费v在线 一区二区三区在线观看欧美精品 | 日韩中文字幕97色伦 |